Drum Kit and Gear

How do you set up your drum set?

How to set up a drum set: throne, bass drum, snare, hi-hat, toms and cymbals in order, with starting positions, posture tips and a final check.

On this page
  1. Short answer
  2. Before you begin
  3. Step 1: Throne
  4. Step 2: Bass drum and pedal
  5. Step 3: Snare drum
  6. Step 4: Hi-hat
  7. Step 5: Toms
  8. Step 6: Cymbals
  9. Step 7: Test and adjust
  10. Posture
  11. Common mistakes

Short answer

Set up your drum kit from the seat outward. Start with the throne at a comfortable height, then place the bass drum and pedal, the snare, the hi-hat, the toms, and finally the cymbals. After each piece, sit down and check that you can reach it comfortably without twisting or overextending. There is no single correct layout; the steps below are a starting point that you adjust to your body.

These instructions are for a right-handed player. If you’re left-handed, mirror them.

Before you begin

  • Choose a spot with a flat floor and space around you. A rug under the kit helps stop it from sliding.
  • Lay out the parts, the drum key and any manuals.
  • If you’re not sure what each piece is, see the drum set guide.
  • If this is a child’s kit, see junior drum set assembly and setup.

Step 1: Throne

Open the legs fully and set the seat so you can sit comfortably with your feet flat. A common starting point is to have your hips slightly higher than your knees, with your thighs sloping gently downward (some teachers describe this as roughly a 90 to 110 degree angle at the hip and knee). Sitting too low tends to tire the legs and can strain the lower back. For a longer discussion, see how to choose a drum throne and set the right height.

Step 2: Bass drum and pedal

Place the bass drum in front of the throne so your right foot can reach the pedal with a relaxed leg. Many players sit slightly off-center, so the drum is angled a little to the left of straight ahead and the right leg falls naturally onto the pedal.

Extend the spurs (the legs on the front of the shell) and angle them slightly forward so the drum doesn’t slide. Clamp the pedal onto the bass drum hoop, centered, and tighten it by hand. The beater should hit near the middle of the head and bounce back. If it sticks, the spring tension is probably too loose; if the pedal feels heavy, loosen it.

Step 3: Snare drum

Open the snare stand’s legs, rest the drum in the basket and tighten the arms. Place it between your knees, a few inches above your thighs, so your sticks can reach the center of the head without hitting your legs or the rim. Keep it mostly flat, or tilt it slightly toward you if that feels more natural. Make sure the snare throw-off lever is positioned where you can reach it.

Step 4: Hi-hat

Set the hi-hat stand to the left of the snare, with the pedal where your left foot rests comfortably. Place the heavier cymbal (usually the unlabeled one) on the bottom, bell side down, and attach the top cymbal with the clutch so it can open and close when you press the pedal. Set the height so your sticks clear the snare and your arms don’t clash when you cross over. A small gap, around an inch or so, between the cymbals when the pedal is up is a typical starting point.

Step 5: Toms

Mount the rack toms above the bass drum, or on a separate stand, angled slightly toward you. Avoid extreme tilts; if the drums don’t fit, adjust the height or move them slightly left or right. Place the floor tom to your right, at about the same height as the snare, and check that all of its legs are even so it doesn’t wobble.

Step 6: Cymbals

Add the crash and ride cymbals on their stands. A typical arrangement puts a crash to the left or between the toms, and the ride over or just above the floor tom, where your right hand can reach it without stretching. Angle the cymbals slightly toward you so the sticks strike the edges or bow cleanly. Don’t overtighten the wing nuts; cymbals should be able to swing a little when hit. If you’re choosing cymbals, see choosing cymbals for a beginner drum set.

Step 7: Test and adjust

Sit down and play around the kit slowly, moving from the snare to each tom and cymbal in turn. Look out for:

  • reaching or leaning to hit anything
  • sticks hitting rims, cymbals or each other
  • your knees touching the snare
  • your foot straining to reach either pedal

Move each piece a little at a time until everything is easy to reach. Make small changes; it’s better to adjust several times than to move many things at once.

Posture

Sit tall without stiffening, with your weight on the seat rather than leaning on your pedals. Keep your arms relaxed and close to your body, and try not to raise your shoulders. Drumming can be physically tiring, so take breaks if you notice tension or pain. Our guide to drumming posture goes into more detail.

Common mistakes

  • Setting the throne too low.
  • Putting the snare too high, which makes wrists and shoulders work harder.
  • Placing cymbals so high that you lift your arms for every hit.
  • Overtightening cymbal wing nuts, which can restrict movement and may damage the cymbal.
  • Never re-checking the setup. Even a good layout needs small tweaks as you improve.

A well-arranged kit is quicker to learn on and more enjoyable to play. Once everything is in place, tune the drums before you start. If you’re wondering about the cost of getting started, see how much drums cost.

The complete guide to drum kit and gear

The Drum Set: Parts Information and Facts
Read the guide

Keep exploring

Guides from other topics

All topics →