Bass Drum

How to Set Up Your Kick Drum and Pedal

Set up your kick drum and pedal step by step: throne height, pedal position, beater angle, spring tension, anti-slip tips and a starting point for tuning.

On this page
  1. Start with where you sit
  2. Positioning the drum and pedal
  3. Beater angle and footboard height
  4. How tight should a kick drum pedal be?
  5. Stop the pedal and drum from sliding
  6. Beater and head: choosing a starting sound
  7. A quick tuning and muffling starting point
  8. Setup checklist

Start with where you sit

Setup starts with the throne, because everything your foot does depends on your leg position. A common starting point is a throne height that gives your thighs a slight downward slope toward your knees. A seat that is too low means your leg works against the angle, which can tire your muscles faster.

Sit at a distance where your feet rest comfortably on the pedals and your arms can reach the snare and toms without stretching. Our guide on how to set up your drum set covers the rest of the kit. Heel-up players often prefer a somewhat higher seat than heel-down players. Our comparison of heel up vs. heel down explains the difference.

Positioning the drum and pedal

  • Place the bass drum where your right foot (or left, if you play left-footed) reaches the pedal naturally with your knee roughly in line with your hip.
  • Clamp the pedal to the bass drum hoop so the footboard sits straight ahead, in line with your leg, not at an angle.
  • The beater should strike somewhere near the center of the batter head. Hitting a little off center changes the tone and feel, so some drummers experiment, but near the center is a sensible start.

Move the drum or pedal a little and play a few notes each time. Small changes in placement can make the pedal feel different.

Beater angle and footboard height

The beater angle is how far back the beater rests from the head. A commonly suggested starting point is about 45 degrees away from the head. A beater set farther back gives it more travel and generally a bigger stroke, while closer gives a shorter throw. Adjust in small steps and listen for what you prefer.

Many pedals also let you change the footboard angle or length of the beater shaft. Keep the footboard at a height where your foot rests comfortably and your ankle is not forced into an awkward position.

How tight should a kick drum pedal be?

Most pedals have a spring tension adjustment screw, usually near the spring. There is no single correct setting, but a useful approach is:

  1. Start in the middle. A medium tension is a sensible beginning because it gives the beater a reasonable rebound without feeling stiff.
  2. Go tighter for more rebound. Faster playing generally needs the pedal to spring back quickly. Many players who focus on speed use medium to high tension.
  3. Go looser for more control and softer playing. Too loose and the beater feels sluggish and does not come back on its own.
  4. Change one turn at a time and play a minute or two of steady notes before changing again.

If the pedal fights your ankle, it is probably too tight. If it feels floppy and slow to rebound, it is probably too loose. Make sure both pedals match if you use a double pedal.

Stop the pedal and drum from sliding

A pedal that creeps forward as you play will throw off your technique. Some ways to deal with this:

  • Use the bass drum spurs (the legs on either side) so the drum stays put.
  • Put the kit on a rug or non-slip mat, or use a drum riser with a rug grip. A carpet or mat can also keep the pedal base from sliding on a hard floor.
  • Check that the pedal clamp is tight against the hoop.
  • Pedals with a plate or spikes underneath can help, depending on the floor surface.

Beater and head: choosing a starting sound

Beaters come in felt, wood and plastic variants. Felt generally gives a rounder tone. Harder wood or plastic beaters give a sharper click, especially on a head with a kick pad or patch. Heads with built-in muffling rings or pads, and patches, also change the attack. If you want a tighter, focused kick, read our guide to getting a punchy bass drum sound.

A quick tuning and muffling starting point

If you are unsure how to tune the drum, a common beginner approach is to tension the batter head (the one you hit) until the wrinkles just disappear, then set the front (resonant) head at the same tension or slightly higher. Then add a small pillow or folded towel inside the drum so it lightly touches the head or heads, and adjust to taste.

Tuning is a personal choice and depends on the drum, the heads and the music. Make small adjustments and listen, or follow our full walkthrough on how to tune your kick drum.

Setup checklist

  • Throne height gives a slight downward thigh slope
  • Drum and pedal are within comfortable reach
  • Footboard is straight and the clamp is tight
  • Beater angle starts around 45 degrees
  • Spring tension starts around the middle
  • Drum and pedal do not slide
  • Batter head tuned and muffled to a starting sound

Once the basics are right, our bass drum lesson for beginners walks you through the basic stroke and your first beat.

The complete guide to bass drum

Bass Drum Lesson for Beginners: Technique and Footwork
Read the guide

Keep exploring

Guides from other topics

All topics →