Can you use a floor tom as a kick drum?
Yes. A floor tom can work as a small kick drum if you add a way to hold it on its side and attach a bass drum pedal. People do this to get a compact kick for jazz, to carry less to gigs, or to add a second, different kick sound to a larger kit.
A converted tom will not sound like a 22-inch rock kick, and it is not meant to. Expect a higher, tighter and more focused tone, which suits quieter and more musical styles.
What you need
- A floor tom. Larger, deeper floor toms (often 16 or 18 inches across) are the usual choice.
- A conversion kit or a mounting solution. Several drum makers and hardware companies sell kits that clip onto the floor tom legs or rim. They provide two legs for the front and a plate or bracket to hold the pedal.
- A bass drum pedal.
Leg diameter is the most important compatibility detail. Floor tom legs and brackets come in different sizes, and the size can vary between makers and even between years from the same maker. Measure your leg diameter and check it against the kit’s specification before you buy. If you are unsure, a drum shop or the kit maker can confirm what fits. Some kits are brand specific and some are advertised as more universal, so do not assume.
Setting up the legs and pedal
In general, the legs slide into two of the drum’s existing leg brackets, and the height of the front of the drum comes from how far you angle the legs. The pedal attaches to a plate on the hoop or tension rods, depending on the kit.
When attaching the pedal:
- Keep the pedal’s drive mechanism clear of the rim and head.
- Do not set the pedal so far back that you lose power, or so close that it touches the drum.
- Make sure the pedal clamps onto enough of the plate that it cannot walk or slip off.
Choosing heads
Resonant head
Because the drum faces you, the front head is the resonant head. A thin head, coated or clear, lets the drum ring more. A coated head tames the ring a little, and a clear head sounds brighter. Some players leave the front head off entirely, which gives a drier, more open sound and makes it easy to place a microphone.
Batter head
You can use a bass drum batter head sized to fit, or the standard tom head you already have. Some bass drum heads include built-in muffling rings. For jazz, a single-ply head often gives more resonance, and a double-ply head gives more control.
Cutting a port hole (optional)
A hole in the resonant head is not required, but it can help the drum project and gives easier access for a microphone. If you decide to cut one:
- Work on a flat, protected surface, such as a piece of cardboard from the head’s box.
- Lay the head on it and use a round object (about 4 to 6 inches across) as a guide.
- Score the line lightly with a sharp craft knife and go around more than once. Trying to cut through in one go can make the knife slip and ruin the head.
Cutting a hole is permanent, so only do it to a head you are happy to commit. If you want to keep using the drum as a floor tom, keep a spare uncut head.
Tuning the converted drum
Tuning a converted floor tom is much like tuning any kick drum, but the smaller shell means it will naturally sit higher.
Batter head
- Seat the head and finger-tighten the rods in a star pattern, then bring it up just to the point where the wrinkles disappear.
- Add a small amount more tension if you want more rebound and attack. A looser head gives a deeper, flappier sound.
- Do not go too loose. A head that is too slack can dent from the beater, and an author who tried a very loose batter head on a converted tom found that sticks dented it when used as a floor tom again.
Check that the pitch is even around the head by tapping near each rod, as described in our main drum tuning guide.
Resonant head
Tune the front head to match or sit a little above the batter head. Because the drum is small, a slightly higher front head tends to give more focus to the low end. If the drum sounds boxy or ringy, lower the front head slightly or add muffling instead of tightening more.
Muffling
A small drum can ring for a long time. Options include a strip of felt resting against the batter head, a muffling ring, or a small amount of padding inside. Use as little as you need. Less muffling is more resonant, and more muffling is drier and punchier.
Setup and beater placement
Where the beater strikes changes the sound. Hitting nearer the center gives a shorter, less resonant note, and hitting nearer the edge lets the head ring more. Adjust the pedal position to find the spot you like. Our kick drum and pedal setup guide covers beater angle and spring tension. If you are using a kick drum microphone, try it both inside the drum and just outside a port hole.
Why do drummers have two floor toms?
Two floor toms give a wider range of low pitches, with one tuned lower than the other. They also give a drummer more places to build fills across the kit. If you are curious about how tom pitches relate to each other, see how to tune toms to musical intervals.
Common problems
- The pedal slips on the plate. Tighten the clamp and make sure it grips enough of the plate.
- The drum sounds weak. Try a port hole, a thinner resonant head or a slightly tighter batter head.
- The drum rings too long. Add a small amount of muffling or lower the resonant head.
- The head is dented. The batter head may be too loose for the way you play it. Tighten it slightly.