What tuning to an interval means
An interval is the distance in pitch between two notes. Tuning toms to intervals means choosing a main note for each tom so that moving around the kit sounds like a deliberate pattern, rather than random thuds. This is helpful for fills that sound like melodies, for recording, and for playing with pitched instruments.
It is optional. Many great drum sounds come from simply tuning by ear until the toms sound good together. But if you want a repeatable, musical spacing, an interval approach gives you a plan.
Common intervals
- Fourths: a common spacing for toms. It gives clearly separate, evenly spaced pitches.
- Fifths: a wider gap, often used when the toms are further apart in size or when you want more separation. A perfect fifth is also a common choice for floor toms.
- Thirds: a closer spacing, which can sound like a chord or a more compact scale.
- Mixed spacing: many kits mix intervals depending on the sizes. That is perfectly normal.
Toms are not perfectly pitched instruments, so what you hear is always approximate. Aim for a clear, pleasant relationship and then adjust by ear.
Before you start: clear each head
Tuning to a note only works if each head is even first. If the lugs disagree with each other, you will hear a wobbly pitch and a pitch reading will jump around.
- Seat the head by pressing it and tightening past your target, then returning to it.
- Finger-tighten all rods and bring them up in small equal turns in a star pattern.
- Tap near each rod and make the pitch match at every lug.
- Move the whole head up or down by turning every rod the same amount.
Our main drum tuning guide describes this process in more detail. Some professional drummers also suggest practicing on a pitched instrument, such as a piano or even an inexpensive melodica, so you get better at hearing pitch.
A step-by-step method
- Pick your notes. Decide what you want each tom to sound like, such as a set of fourths from high to low. Write them down.
- Tune the resonant head first (or whichever head you prefer to start with), getting it clear and to the pitch you want.
- Tune the batter head so it relates to the resonant head the way you like. Common options are the same pitch or a little lower.
- Check the drum as a whole. Hit the drum normally and listen to the note that rings. That is the pitch you are tuning, not the pitch of the tapped head.
- Adjust in small steps until the drum’s main note matches your target.
- Move to the next drum and repeat. Work through the drums in order and compare each against its neighbor.
One engineer’s approach, from a published tuning guide, is to tune the resonant head about a half step below the final pitch he wants, then tune the batter a minor third below the resonant. That is one method among several, and other drummers set the heads to the same pitch or put the resonant head higher. Try different head relationships on a single tom and trust your ears.
Starting pitch ranges by size
The table below shows suggested starting notes for single drums, from one engineer’s guide. These are not rules, but a reasonable place to begin.
| Tom size | Suggested range |
|---|---|
| 8” | F to F# |
| 10” | C# to D |
| 12” | A# to B |
| 13” | F# to G |
| 14” | about E |
| 15” | D to D# |
| 16” | C to C# |
| 18” | A# to B |
The same source warns against moving far outside these ranges, for example more than about a half step either way. In general:
- Tuning too high can bring out more overtones and less fundamental note. Gel or tape may then be needed to focus the sound.
- Tuning too low can make the drum sound flappy, make it harder to keep in tune, and make heads easier to dent.
Your drums, heads and room will differ, so use the table as a guide and not a target.
Example setups
The same guide suggests note choices for several set sizes. For example:
- 10, 12 and 14 inch toms: about D, A and E (fourths and fifths).
- 10, 12 and 16 inch toms: about D, A and C.
- 10, 13 and 16 inch toms: about D, G and C (fourths).
If you play a different combination, work out the spacing by ear and adjust.
Why drum sizes matter
Even intervals need enough difference in size. According to the same guide, a two-inch size difference between drums is not enough to get fourths while keeping each drum in its best range. A difference of about three inches, for example 10, 13 and 16 inches or 12, 15 and 18 inches, is better suited to evenly spaced intervals.
If your sizes do not allow the exact spacing you want, choose the best compromise rather than forcing a drum outside its comfortable range. A floor tom at the bottom of the kit can also be tuned relative to a kick drum so the two do not clash.
Problems and fixes
- The note keeps changing as you tune: check that the lugs are matched. Uneven lugs produce a moving pitch.
- Too many overtones: try lowering the pitch slightly, matching the lugs again, or adding a small amount of muffling.
- A drum sounds dead: loosen the muffling or raise the resonant head slightly.
- Tuning will not hold: see why drums go out of tune and how to keep them stable.
Tools
A pitch-reading tuner, such as a Tune-Bot, can show the note at each lug and help you hit a target. A tension gauge gives repeatable numbers, but not note names. Neither replaces your ear. The tools help you get close faster, and the final decision comes from listening.